Parking Garage Restoration System Instruction Sheet

A Super Bonding, Flexible Cementitious Coating for Parking Garage Weatherproofing (Waterproofing if Required) and Restoration.

Weatherproofing is used over sound substrates where no leakage or water penetration has occurred.

Waterproofing is needed if water penetration has taken place in order to restore surface integrity and prevent further leakage.

ADVANTAGES

• Cost Effectie - Easy to Apply
• Bonds Securely to Properly Prepared Concret Substrate
• Short Down Time - Fast Curing
• High Flexural Strength - Will Withstand Moderate Flexing Unlike Most Repair Materials
• High Impact and Abrasion Resistance
• Resistant to Water and Moisture Penetration, Salt Spray and Most Chemicals
• Freeze-Thaw Resistant
• Waterbased - Environmentally Safe to Use and Apply

SEE TEST DATA

SURFACE PREPARATION
Substrate must be structurally sound.
Remove any grease, oil, paint, dust, dirt, sealers, laitence, curing compounds and other foreign materials which may prevent proper bonding. Use shotblast, sandblast or waterblast with sand injector (minimum 3,500 psi). To remove heavy grease, use biodegradable degreasers and hot steam cleaning machine.

Fill cracks with SPEED MIX 2000, vigorously field mixed to disperse and wet all particles. Use margin trowel to clear vessel walls. Trowel over cracks approximately 5" on each side to create an even profile with the adjacent substrate. Allow to cure 2-4 hours, depending on ambient temperature.

Roll a coat of MULASTICOAT ® over cracks. Embed Stitch Bonded Polyester Fabric in wet MULASTICOAT ®. Roll additional MULASTICOAT ® over the Polyester Fabric and allow to cure a minimum of  24 hours, longer in cooler weather.
If MULASTICOAT ® is exposed for more than 72 hours before application of other materials to entire surface, a thin coat of KRETE KOTE 2000 should be applied to protect MULASTICOAT ®.

CRACK REPAIR WITH SPEED BOND (SEE CRACK REPAIR SYSTEM).

WATERPROOFING ENTIRE SURFACE WITH MULASTICOAT ®

SQUEEGEEING KRETE KOTE

ALLOW TO DRY MIN. 48-72 HOURS BEFORE OPENING TO TRAFFIC

KRETE KOTE 2000, resurfacing material, is field mixed with water to desired consistency. Ratio approximately 1 ¼ - 1 ½ gallons of water to 65 lb bag (see KRETE KOTE system instructions).

FIRST COAT - Apply with squeegee, and allow to dry (usually about 1-2 hours).
SECOND COAT - Apply same as first coat.
THIRD COAT - if texture is desired, apply KRETE KOTE with hopper gun for French Lace Texture, or roll with ¼" texture roller for texture finish.
COLORSEAL - If staining is a concern, use two coats of COLORSEAL. (Refer to COLORSEAL "Instructions for Use.") Allow minimum 24 hour cure before applying COLORSEAL.

ALLOW TO CURE MINIMUM 72 HOURS BEFORE ALLOWING VEHICLE TRAFFIC

Each gallon of MULASTICOAT ® will cover approximately 40-50 sq. ft. (2 coats) or about 350 lineal feet over repaired cracks.

Each Gallon of COLORSEAL will cover approximately 200 sq. ft. when applied per instructions.

LIMITATIONS
Do not apply when substrate surface temperature is below 50°F, above 100°F, if ambient temperature is below 50°F and falling, over 100°F and rising, or if precipitation is expected within a 24 hour period.

PACKAGING AND STORAGE
KRETE KOTE 2000 is furnished in 65 lb bags.
MULASTICOAT ® AND COLORSEAL in 1 and 5 gallon pails.
STITCHBONDED POLYESTER FABRIC - 10" wide rolls, 324 ft. long.
Store in dry area at 40° - 90°F
Shelf life approximately 9 months in unopened containers.

WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturers’ specifications. Seller makes no other warranty, expressed or implied, regarding the use of its products. Since use of the product is beyond the Seller’s control, the Buyer assumes all risks of use. Seller’s sole obligation shall be to replace material if found to be defective. Seller shall not be liable for any damages, injury, loss, direct or indirect or consequential, resulting from use of its products.

back to PARKING GARAGE RESTORATION SYSTEM