SURFACE PREPARATION
Substrate must be structurally sound, free from grease, oil, paint, dirt, dust and sealers. Laitance, curing compounds and any other foreign material which may prevent proper bonding. When applying to any cementitious surface, that surface must be fully cured. Water should be able to penetrate the substrate. If water beads, surface contaminates are present. Insure that surface is not subjected to hydrostatic pressure, if so, do not apply. Concrete slabs and mortar beds should have a coarse finish to assist in bonding. When applying to Gypsum and Lightweight Cement the substrate must have a minimum of 2,000 psi compressive strength. Must be dry and properly cured. Roughen the surfaces by sanding or scarifying, rinse and allow to dry. Do not sand floors that contain asbestos.
APPLICATION
Step 1: FLEX SET MORTAR is to be field mixed with clean potable water and mechanically mixed to desired consistency based upon scope of application. Add approximately 6-1/2 quarts of water into mixing container. Slowly pour the contents of the bag into the mixing water. Mix until a firm, workable consistency is achieved. If more water is needed, add small amounts and continue to mix until consistency is achieved. Let the mixture slake or stand 5 to 10 minutes, then stir again and use. Stir occasionally but do not add more water. Desired consistency should be trowel ridges should stand without slumping. Do not exceed a total volume of 1.5 gallons or water for each 65-lb. bag. Be sure mixed material is consistent from batch to batch.
Step 2: Apply FLEX SET MORTAR to substrate with flat trowel. Use a properly sized notch trowel to insure proper coverage and spread of material under tiles. Work placed FLEX SET MORTAR with notched trowel to create rows of adhesive to proper thickness for item being placed. Press tile firmly in place, moving back and forth to insure a proper set. Adjust tile quickly and then gently tap into place with rubber mallet or beating block until flush with other units. Periodically pull up a tile or stone and check the back to insure proper adhesive coverage. If mortar has already taken its set under the lifted tile, remove mortar and replace with fresh FLEX SET MORTAR can be a total of 3/8″ thick once item has been set and tamped into place.
Step 3: Curing time will vary due to weather conditions, thickness, substrate absorption, etc. Material should be protected from weather elements and foot traffic for a minimum of 24 hours. Provision for movement (expansion joints and control joints) and other changes of plane in all installations are required. Do not bridge expansion or control joints. Those joints should be brought up through the work and filled with a suitable caulking.
SIZES:
- 50 lb bag
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Click the Safety Data Sheet below to download
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
1. Multicoat system has been properly applied by a certified applicator.
2. Problem is determined to be due to defect of Multicoat Corporation’s products.
3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane.
Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, de-bonding and water intrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
1. Use only a licensed contractor in good standing (fully bonded).
2. Make certain that the applicator has been certified by Multicoat, prior to work
commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in
good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within
manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the
Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential,
resulting from its products. The parties intend that the limitation of damages,
including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
FLEX SET MORTAR
TOP-LEVEL POLYMER MODIFIED THIN SET
Multicoat’s FLEX SET MORTAR is a top-tier polymer-modified mortar adhesive designed to set various materials, including tile, glass, stone, brick, brick veneer, and rock. One of its standout features is its versatility, as it can be effectively used underwater.
Bag
APPLICATION
Field mixed in the approximate amount of 2 to 2-1/2 gallons of Liquid Catalyst per bag, preferably with a special MULTICOAT Mixing Paddle. (More or less liquid catalyst may be needed depending upon ambient temperature.
Mix vigorously to disperse all lumps and to thoroughly wet all particles. Suggest 1-11⁄2 minutes after all dry material added. Use margin trowel to clear vessel walls. For best results let cement mix stand in bucket for 3-5 minutes then add a small amount of Liquid Catalyst to re-break material. This will give the material additional pot life.
Check for consistency by applying with a 11⁄4” nap roller. Applied material should peak not slump.
If too thick small clumps will come away with roller. Add small amount of Liquid Catalyst, remix and retest. If material slumps add solids, remix and retest. Dampen pool substrate with water before application.
SIZES:
- 5 Gallon Bucket
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Click the Safety Data Sheet below to download
SAFETY DATA SHEET
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
1. Multicoat system has been properly applied by a certified applicator.
2. Problem is determined to be due to defect of Multicoat Corporation’s products.
3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane.
Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, de-bonding and water intrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
1. Use only a licensed contractor in good standing (fully bonded).
2. Make certain that the applicator has been certified by Multicoat, prior to work
commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in
good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within
manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the
Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential,
resulting from its products. The parties intend that the limitation of damages,
including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
LIQUID CATALYST
ACRYLIC ADDITIVE
A proprietary additive blend that enhances the bonding, tensile, and water resistant properties of many cement bag mixes.
Bucket
APPLICATION
Remove all dirt, oil, loose paint, frost and other contamination from all working surfaces. Maintain Flex-C (L) at room temperature before applying to ensure easy gunning and tooling. Test and evaluate to ensure adequate adhesion. Carefully gun the sealant with a smooth, continuous bead. If tooling is needed, do so within fifteen minutes of application.
CONCRETE
Prior to application remove any residual contamination by mechanical abrasion, sand blasting or power washing. On green concrete, remove all release agents and loose concrete. Dry all visible and/or standing water. Install an appropriate backer rod to avoid three-point bonding.
METAL
Prepare all metal to ensure maximum adhesion. Remove all rust, scale and residue using a wire brush. Remove films, loose or inappropriate coatings and oils with an appropriate solvent such as alcohol.
*Multicoat recommends that coated substrates be tested for proper adhesion prior to starting a project to determine suitability for use.
WOOD
Wood should be clean, sound and dry prior to sealant application. Allow treated wood to weather for six months prior to application. Remove all coatings and paint to ensure proper adhesion. Flex-C (L) is not recommended for use on fire retardant lumber.
PRIMING
In most applications Flex-C (L) will not require a primer. However, certain substrates may require a primer to ensure a long lasting bond and weatherproof seal. It is the applicator’s responsibility to determine whether or not a primer is needed in their specific application.
SIZES:
- 10.3 oz Tubes
- 20 oz Sausages
- 64 oz Pouches
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
FLEX-C (L)
SELF-LEVELING ADHESIVE SEALANT CAULKING
FLEX-C (L)® is a Self-Leveling Joint Sealant. FLEX-C (L) offers robust, flexible sealing capabilities, especially for joints that require more than 35% compression and extension. FLEX-C (L) boasts an eco-friendly composition, free from solvents or isocyanates, and emits minimal VOCs. Additionally, it has a subtle scent and is composed of 100% solids. FLEX-C (L) employs the advanced moisture cure hybrid polymer technology. This means it reacts and forms links when exposed to moisture, ensuring a long-lasting seal. This seal has exceptional resistance to weather and UV rays and functions efficiently in temperatures ranging from -40o F to 200o F.
- ASTM C920 Type S, Grade NS, Class 35 Uses NT, T, G, A, M, and O.
- Solvent and isocyanate free
- Non-silicone
- Non-flammable
- Fast curing
- Multiple colors available
- Permanently elastic in a broad temperature range
- Paint compatible
- Low odor
- Extremely low shrinkage
Tube
Sausage
Pouches
APPLICATION
Remove all dirt, oil, loose paint, frost and other contamination from all working surfaces. Maintain Flex-C at room temperature before applying to ensure easy gunning and tooling. Test and evaluate to ensure adequate adhesion. Carefully gun the sealant with a smooth, continuous bead. If tooling is needed, do so within fifteen minutes of application.
CONCRETE
Prior to application remove any residual contamination by mechanical abrasion, sand blasting or power washing. On green concrete, remove all release agents and loose concrete. Dry all visible and/or standing water. Install an appropriate backer rod to avoid three-point bonding.
METAL
Prepare all metal to ensure maximum adhesion. Remove all rust, scale and residue using a wire brush. Remove films, loose or inappropriate coatings and oils with an appropriate solvent such as alcohol.
*Multicoat recommends that coated substrates be tested for proper adhesion prior to starting a project to determine suitability for use.
WOOD
Wood should be clean, sound and dry prior to sealant application. Allow treated wood to weather for six months prior to application. Remove all coatings and paint to ensure proper adhesion. Flex-C is not recommended for use on fire retardant lumber.
PRIMING
In most applications Flex-C will not require a primer. However, certain substrates may require a primer to ensure a long lasting bond and weatherproof seal. It is the applicator’s responsibility to determine whether or not a primer is needed in their specific application.
SIZES:
- 10.3 oz Tubes
- 20 oz Sausages
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
FLEX-C
ADHESIVE SEALANT CAULKING
FLEX-C® is a superior joint sealant suitable for numerous construction uses. FLEX-C offers robust, flexible sealing capabilities, especially for joints that require more than 35% compression and extension. FLEX-C boasts an eco-friendly composition, free from solvents or isocyanates, and emits minimal VOCs. Additionally, it has a subtle scent and is composed of 100% solids. FLEX-C employs the advanced moisture cure hybrid polymer technology. This means it reacts and forms links when exposed to moisture, ensuring a long-lasting seal. This seal has exceptional resistance to weather and UV rays and functions efficiently in temperatures ranging from -40o F to 200o F.
- ASTM C920 Type S, Grade NS, Class 35 Uses NT, T, G, A, M, and O.
- Solvent and isocyanate free
- Non-silicone
- Non-flammable
- Fast curing
- Multiple colors available
- Permanently elastic in a broad temperature range
- Paint compatible
- Low odor
- Extremely low shrinkage
SURFACE PREPARATION
Surface must be completely dry and thoroughly clean of any foreign material that may interfere with bonding. Cracks larger than 1/16” in width must be opened with a crack chaser to a minimum of 1/4” in width. Once opened, all cracks must be cleaned by sand-blasting, waterblasting
or water sandblasting. Depth of crack and surface area around crack must be completely dry and thoroughly clean.
APPLICATION
Prepare Cartridge: Unscrew round colleet, pull cap from center of tube and set both to the side for later use. Screw enclosed mixing tip onto tube insuring snug fit.
Initial Dispense: Prior to filling crack, insure material is flowing through mixing tip uniformly and easily. Dispense onto discarded cardboard as a test.
Begin filling crack to a slightly over filled capacity, then immediately press SPEED BOND into crack and spread material level and flat onto adjacent sides of crack by using a margin trowel or putty knife. While SPEED BOND is wet, broadcast #16-20 silica sand generously over the wet SPEED BOND and allow to set until dry. Once dry, brush away and sand that has not stuck to the SPEED BOND. The crack is now ready to be over-coated. Speed Bond is self leveling, and large cracks that are completely open should be dammed closed to prevent the SPEED BOND from leaking out the bottom.
Reuse: Partially used tubes can be stored and re-used. Remove the used mixing tip and discard as they can not be re-used. Attempting to re-use a used mixing tip will damage the tube and render it useless. After used tip has been removed, wipe excess material from end of cartridge, re-install the cap and collet.
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Click the Safety Data Sheet below to download
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
SPEED BOND
URETHANE CRACK REPAIR CAULKING
Speed Bond is a two-part, self leveling, rapid set, urethane caulking used to fix cracks in horizontal concrete. Sets up fast like an epoxy, however the urethane composition allows it to remain somewhat flexible. Each tube comes with 1 mixing tip. Uses a standard caulking gun.
SURFACE PREPARATION:
Substrate must be structurally sound, free from grease, oil, paint, dirt, dust, sealers, laitence, curing compounds, and any other foreign material which may prevent proper bonding.
MIXING:
MULTI-BASE is field mixed with clean potable water to desired consistenancy based upon scope of application. Add 1-1/4 to 2 gallons of water per bag. Mix vigorously with a MULTICOAT® Cage Mixer to disperse all lumps and to thoroughly wet all particles. Adjust to desired consistenancy by addition of dry material or small amount of water. Mix thoroughly for a maximum of 3 minutes. For best results allow material to set for 3 to 5 minutes, then add a small amount of water and re-break the material. Re-temper as needed.
APPLICATION:
Multi-base is designed to be used in conjunction with other MULTICOAT® Materials and Systems. Please see the reference for various systems as listed below.
For use in:
Above Grade Waterproofing: See instruction sheet for “MULTI-DECK WATERPROOFING SYSTEM for Wood”.
SIZES:
- 65 lb bag
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Click the Safety Data Sheet below to download
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
MULTI-BASE
LATH BASE COAT
Multi-Base is a polymer modified concrete to be used over metal lathe as a base coat for the above grade system for wood decks.
- Single Component Packaging
- Easy to Apply
- Just Add Water
- High Compressive & Flexural Strength
- Outstanding Bond Strength to Most Building Materials
- Superior Impact and Abrasion Resistance
- Weather and Freeze-Thaw Resistant
Bag
SURFACE PREPARATION:
Substrate must be structurally sound, free from grease, oil, paint, dirt, dust, sealers, laitence, curing compounds, and any other foreign material which may prevent proper bonding. Cracks and imperfections must be repaired prior to application.
APPLICATION:
For use as a base coat over metal lath or fiberglass mesh: Apply STUCCO BASE to the substrate thick enough to cover the outline of the mesh or lath. The outline of the mesh or lath can be visible but should not be felt. Thickness of the STUCCO BASE will vary due to thickness of the lath or fiberglass mesh being used.
SIZES:
- 50 lb bag
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Click the Safety Data Sheet below to download
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
1. Multicoat system has been properly applied by a certified applicator.
2. Problem is determined to be due to defect of Multicoat Corporation’s products.
3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane.
Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, de-bonding and water intrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
1. Use only a licensed contractor in good standing (fully bonded).
2. Make certain that the applicator has been certified by Multicoat, prior to work
commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in
good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within
manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the
Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential,
resulting from its products. The parties intend that the limitation of damages,
including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
STUCCO BASE
STUCCO BASE
Multicoat’s STUCCO BASE is a polymer modified cementitious base coat designed to be used vertically as a base coat for hard coat stucco systems. STUCCO BASE is designed to be used as a base coat under synthetic stucco finishes such as Multicoat’s MULTI-TEX® STUCCO MIX.
Bag
SURFACE PREPARATION
POOLS
- Check and completely remove all hollows and loose areas with picks and hammers. Chip out minimum 2 inches below tile line and around all water inlets, return lines and light fixtures. Sandblast, acid etch or water blast with a turbo nozzle or sand injection attachment (3,500 psi minimum). If acid etching, must neutralized and powerwash with spinner tip. Make sure to remove all rust, algae, copper sulfate, soft flaky plaster, paint and other foreign matter. Recheck for hollows, loose and flaky areas. Soft flaky areas must be removed before SCRATCH KOTE 2000 is applied. Wash thoroughly with waterblaster and dry all areas to touch before proceeding.
WALLS & FLOORS
- Substrate must be structurally sound, free from grease, oil, paint, dirt, dust, sealers, laitence, curing compounds and other foreign materials which may prevent proper bonding. Cracks and imperfections must be repaired. Properly installed expansion joints should be cleaned.
MIXING
- Using a mixing paddle, mix with 2-2.5 gallons of LIQUID CATALYST* per bag for 1.5 minutes. Mix vigorously to disperse all lumps and to thoroughly wet all particles. Use margin trowel to clear vessel walls. For best results, let the Scratch Kote sit in the mixing bucket for 3-5 minutes, then add a small amount of water to rebreak the material. This will give the material additional pot life.
*More or less LIQUID CATALYST may be needed depending upon ambient temperature.
APPLICATION
- Dampen the substrate prior to application
- Apply material with a hopper gun, pressure sprayer or a ¾”-1¼” nap roller. Applied material should peak, not slump.
- If too thick – small clumps will come away with roller.
- Add small amount of LIQUID CATALYST, remix and retest.
- If too thin – material will slump.
- add small amounts of 2-Part Scratch Kote Mix, remix and retest.
- If too thick – small clumps will come away with roller.
ALLOW TO CURE FOR A MINIMUM OF 24 HOURS BEFORE APPLYING POOL PLASTER
*LONGER IN COOL WEATHER OR INDOOR APPLICATIONS – 48 to 72 HOURS IS IDEAL.
SIZES:
- 65 lb bag
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Click the Safety Data Sheet below to download
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
FOAM BASE
BASE COAT
FOAM BASE is a base coat used in the Insulated Concrete Form Stucco System. It is a polymer modified cementitious material which is mixed with water on the job. It is applied by a trowel method to the wall, then a woven fiberglass mesh is embedded into the foam base to create a hard, durable, smooth base coat for the stucco mix.
Bag
SURFACE PREPARATION:
Smooth primed fibercement siding must be structurally sound, and surface must be free from grease, oil, paint, dirt, dust, sealers, laitence, and other foreign materials that may PREVENT PROPER BONDING. Proper expansion joints should be installed according to applicable local building codes or structural engineer. (Recommended: Approximately every 16 feet.)
NOTE: A moisture barrier or house wrap may be necessary in some applications. Check local building codes or structural engineer.
APPLICATION
Apply a skim coat of smooth stucco over all joints and corners, allow to dry. Then apply Multicoat STUCCO MIX directly to wall board with trowel or sprayer, and finish to desired texture.
Do not apply if wall board surface temperature is below 50°F, or over 100°F.
Do not apply if ambient temperature is less than 50°F and falling, over 100°F and rising, or if precipitation or extreme high humidity is expected within a 12-hour period.
SIZES:
- 5 Gallon Bucket
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Click the Safety Data Sheet below to download
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
MULTI-LASTIC STUCCO
ELASTOMERIC STUCCO
MULTI-LASTIC® is a one-coat ELASTOMERIC stucco system, designed for its cost effectiveness as well as its ease of application. Being a durable and weather-resistant finish, we recommend it for all wood and steel framed structures (residential & commercial).
Bucket
SURFACE PREPARATION:
Smooth primed fibercement siding must be structurally sound, and surface must be free from grease, oil, paint, dirt, dust, sealers, laitence, and other foreign materials that may PREVENT PROPER BONDING. Proper expansion joints should be installed according to applicable local building codes or structural engineer. (Recommended: Approximately every 16 feet.)
NOTE: A moisture barrier or house wrap may be necessary in some applications. Check local building codes or structural engineer.
APPLICATION
Apply a skim coat of smooth stucco over all joints and corners, allow to dry. Then apply Multicoat STUCCO MIX directly to wall board with trowel or sprayer, and finish to desired texture.
Do not apply if wall board surface temperature is below 50°F, or over 100°F.
Do not apply if ambient temperature is less than 50°F and falling, over 100°F and rising, or if precipitation or extreme high humidity is expected within a 12-hour period.
SIZES:
- 5 Gallon Bucket
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Click the Safety Data Sheet below to download
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
MULTI-TEX STUCCO
ACRYLIC STUCCO
MULTI-TEX® is a one-coat stucco system, designed for its cost effectiveness as well as its ease of application. Being a durable and weather-resistant finish, we recommend it for all wood and steel framed structures (residential & commercial).
Bucket