System
Below Grade Waterproofing
THE MOST RELIABLE AND EASY TO USE BELOW GRADE SYSTEM
The BG 2000 System is a unique waterproofing system for below grade applications. It is strong enough to withstand sharp backfill without a protection board/coating, but also flexible enough to stretch 3 times its original shape. With all that performance, did we mention that it’s also a soil/green friendly product?
- High Flexibility
- Durable
- Cost-Effective
- Easy to Apply
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- BG2000
- Per Gallon: 35-45 ft 2
*OPTIONAL – Apply Vapor Shield to the substrate to reduce the green window of concrete, prevent efflorescence, and/or resist hydrostatic pressure coming through wall. Apply with a pump sprayer in conjunction with water, back to back. Repeat for a total of 2 coats. Allow 24 hours to dry prior to application of BG2000.
Spray one (1) heavy coat or roll two (2) coats of MULASTICOAT® BG 2000 over area to be waterproofed at a coverage rate of 35-45 sq. ft. per gallon. ROLLING: use a 3/4″ nap roller and saturate the roller completely. Heavy coats are recommended. Use a mil thickness gauge to ensure achievement of at least two 20 mil coats. SPRAYING: use an airless paint sprayer, any grade will do. For peak performance, use a .025″ – .027″ spray tip. An easy way to achieve the right coverage when spraying is to mark off a 200 sqft area and use an entire 5 gallon bucket to cover that marked area.
Tensile Bond Adhesion to Concrete Tensile Strength
Method: ASTM C-297 Result: 335 psi (coh/adh)
Tensile Strength
Method: ASTM D-412 Result: 399 psi
Elongation
Method: ASTM D-412 Result: 319.3%
Hydrostatic Head
Method: 12” Water/Film @ 40mil Result: Pass 96 Hrs/no effect
Hydrostatic Pressure
Method: ASTM C-1306 Result: Pass >45 psi*
*The test procedure only calls for taking the pressure to 45 psi but after passing so easily, test was taken up to 80 psi for 3 hours and surface still did not leak.
Q: Can BG2000 be applied to green concrete?
A: For applications with at least one exposed side, YES. As long as it is firm to touch and cleaned of mold releases and other impurities. Things like: poured in place retaining walls, freshly built block walls, etc. are perfect applications for BG2000.
Q: Is BG2000 oil-based?
A: No, there is no asphalt emulsion in BG2000. Unlike many competitors that claim to be “water-based” but also contain petroleum byproducts, BG2000 is made from 100% Water born acrylics and contains ZERO ASPHALT EMULSION.
Q: Is BG2000 expensive?
A: No, when used in replace of lower end asphalt products consumers see a cost decrease due to its higher coverage rates, lower application time, and clean up time/ease.
Q: How do you bridge expansion joints and wall/floor 90º joints?
A: We recommend embedding a material called Polyester Stitch Bond Fabric into the first coat of BG2000 to act as a reinforcement material for high movement areas. It is an inexpensive way to ensure security and rigidity in areas that may be subject to extreme movement over time.
System
Below Grade Waterproofing
BEST FOR JOBS VULNERABLE TO HIGH MOVEMENT
The Premium Below Grade system is comprised of a high-end water-based acrylic waterproof membrane, and a polymer modified cement to achieve the highest flexibility and abrasion resistance possible. The Premium Slatex System is perfect for poured in place walls, concrete block, planters, retaining walls, and so much more.
- High Flexibility
- Super Bonding
- Sprayable
- Easy to Apply
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- VAPOR SHIELD*
- VAPOR SHIELD*
- MULASTICOAT*
- Per Gallon: 75 – 150 ft 2
- Per Bag: 125 – 150 ft 2
- Per Gallon: 35 – 45 ft 2
*OPTIONAL – Apply Vapor Shield to the substrate to reduce the green window of concrete, prevent efflorescence, and/or resist hydrostatic pressure coming through wall. Apply with a pump sprayer in conjunction with water, back to back. Repeat for a total of 2 coats. Allow 24 hours to dry prior to application of Mulasticoat
Enhance user experience with Advanced Tabs, allowing seamless content navigation. Organize information efficiently while keeping the interface clean and interactive. Perfect for FAQs, product details, or multi-section content.
Tensile Bond Adhesion to Concrete Tensile Strength
Method: ASTM C-297 Result: 162 psi (cohesive)
Tensile Strength
Method: ASTM D-412 Result: 99 psi
Elongation
Method: ASTM 2370 Result: 1,086%
Hydrostatic Head
Method: 12” Water/Film @ 40mil Result: Pass 96 Hrs/no effect
Hydrostatic Pressure
Method: ASTM C-1306 Result: Pass >45 psi*
*The test procedure only calls for taking the pressure to 45 psi but after passing so easily, test was taken up to 80 psi for 3 hours and surface still did not leak.
Weatherometer
Method: ASTM G23 Result: 2000 hrs Passed
Compressive Strength
Method: ASTM C109 Result: 2595 PSI @ 45 Day Air Cure
Abrasion Test
Method: ASTM 1242A Result: 1000 Cycles/1000 Grams
Freeze Thaw
Method: ASTM C67 Result: 50- Cycle Pass
Impact Resistance
Method: MIL-D-3134F Result: Pass
For Safety Data Sheets, visit our “Resources” page
Q: Can The Premium Slatex System be used to waterproof poured in place walls?
A: Yes, the Mulasticoat waterproof membrane can be used on poured in place walls, just be sure to use water-based form release and clean the wall of it prior to application so Mulasticoat can bond properly to the concrete.
Q: Is The Premium Slatex System green friendly?
A: Yes, the VOC (volatile organic compounds) content in the products are less than 5 grams/liter. All of the products used are water-based as well. Unlike many competitors that claim to be “water-based” but also contain petroleum byproducts, Mulasticoat is made from 100% water born acrylics and contains ZERO ASPHALT EMULSION.
Q: Is the Premium Slatex System expensive?
A: The Premium Slatex System is cost effective when comparing it to other high end below grade waterproofing systems. This system is best used for situations that require superior elongation performance. For an industry leading economical system see “The BG2000 System”
Q: How do you bridge expansion joints and wall/floor 90º joints?
A: We recommend embedding a material called Polyester Stitch Bond Fabric into the first coat of Mulasticoat to act as a reinforcement material for high movement areas. It is an inexpensive way to ensure security and rigidity in areas that may be subject to extreme movement over time.
System
Air & Vapor Barrier
A SEAMLESS, HIGH PERFORMANCE AIR BARRIER SOLUTION
MULTI-AIR BLANKET is a water based and environmentally friendly seamless air and vapor barrier membrane. The BLANKET as a fluid applied air and vapor barrier provides an effective and economical means of protecting the structure long-term. It can be applied over gypsum and cement-based sheathings, OSB, plywood, CMU, and concrete.
- No Seams
- Fast Drying
- Highly Flexible
- Cost-Effective
- FIRE / SALT
- FREEZE / THAW
- UV
- WATER VAPOR
- MULASTICOAT
- Per Gallon: 100 – 150 ft2
Apply Mulasticoat with a sprayer or roller lighter than normal. Saturate Polyester Stitch Bond Fabric with Mulasticoat on all joints and seams. *Coverage should triple in comparison to its normal below or above grade waterproofing coverage rate as it only needs to be 10 mils thick.
Tensile Bond Adhesion to Concrete Tensile Strength
Method: ASTM C-297 Result: 162 psi (cohesive)
Tensile Strength
Method: ASTM D-412 Result: 99 psi
Elongation
Method: ASTM 2370 Result: 1,086%
Hydrostatic Head
Method: 12” Water/Film @ 40mil Result: Pass 96 Hrs/no effect
Hydrostatic Pressure
Method: ASTM C-1306 Result: Pass >45 psi (.0003 Perms)
Crack Bridging
Method: ASTM C1305 Result: Pass (1148% Elongation)
Nail Sealability
Method: ASTM D1970 – Sec. 7.9 Result: Pass (with fabric)
Q: Can you use a sprayer to apply Mulasticoat?
A: Yes, the Mulasticoat can be sprayed using an airless sprayer.
Q: Is The Air Barrier System green friendly?
A: Yes, the VOC (volatile organic compounds) content in the products are less than 5 grams/liter. All of the products used are water-based as well. Unlike many competitors that claim to be “water-based” but also contain petroleum byproducts, Mulasticoat is made from 100% water born acrylics and contains ZERO ASPHALT EMULSION.
Q: Is the Air Barrier System expensive?
A: The Premium Slatex System is cost effective when comparing it to other Vapor/Air Barrier Systems. This system typically also outperforms traditional house wrap due to its lack of seals and penetration into the substrate.
Q: How do you bridge expansion joints and wall/floor 90º joints?
A: We recommend embedding a material called Polyester Stitch Bond Fabric into the first coat of Mulasticoat to act as a reinforcement material for high movement areas. It is an inexpensive way to ensure security and rigidity in areas that may be subject to extreme movement over time.
System
Above Grade Waterproofing
A DURABLE, LONG-LASTING DECKING SOLUTION WITH PREMIUM AESTHETICS
The MULTI-DECK SYSTEM FOR WOOD SUBSTRATES is a multi-layer, waterproofing, and decorative protective coating designed for above grade wood decks. The system is designed to withstand heavy foot traffic on decks, ramps, walkways, etc.
- Easy To Apply
- Waterproof
- Resists Cracks
- Long-Lasting
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- METAL LATH
- MULTI-BASE
- MULASTICOAT
- KRETE KOTE*
- COLORSEAL
- Per Piece: 21 ft 2
- Per Bag: 40 – 60 ft 2
- Per Gallon: 45 – 50 ft 2
- Per Bag: 125 – 150 ft 2
- Per Gallon: 150 – 200 ft 2
Over 2.5 galvanized metal lathe in a staggered pattern over the entire plywood/OSB surface overlapping the metal flashing to the edge of the deck surface. Mix MULTI-BASE per instructions on the bag and pour over the metal lathe. Trowel onto the deck covering the metal lathe and allow to dry completely.
MULASTICOAT® is then applied over entire surface in two (2) coats with roller, using firm pressure. Embed POLYESTER STITCH BOND FABRIC in the first coat while wet over all flashings. First coat is considered “dry” when dry to the touch which is usually 1-2 hours depending on ambient temperature. The second coat is applied crisscross to the first coat. Broadcast silica sand over wet material to promote mechanical bonding to the following protective decorative finish. After product has dried for a minimum of 24 hours, or longer for cold weather, brush off lose sand before applying a decorative wearing surface.
Apply Krete Kote or Top Coat in 2 steps: a base coat, and a texture coat. Apply a smooth thin layer with a trowel, sprayer or magic trowel and allow to dry. Then apply a texture on top top desired aesthetic look.
Apply the diluted COLORSEAL with nap roller for the 1st coat with very firm pressure. (1/2” nap roller for smooth and 3/4” nap roller for rough surfaces). Allow a minimum of one (1) hour to dry. For the 2nd coat, apply at full strength. Airless sprayers may be used for the 2nd and final coat. Allow final coat a minimum of 24 hours before placing area into use. Will fully cure in 14 days, during which care should be exercised against excessive abuse.
Q: Can Wood Multi-Deck be applied over my existing waterproofing?
A: No, it is best practice to remove an old, failing system before applying a new waterproofing system such as The Multi-Deck System – Wood Substrates.
Q: Can I skip the lath and Multi-Base steps and apply the waterproofing directly to the wood surface?
A: No, the lathe and the Multi-Base restrict the movement of the deck and provide more structure to the surface. It is necessary to fight thermal expansion and contraction and gives an added fire resistance to the system.
Q: Is Multi-Deck expensive?
A: Comparing different systems on the market, Multi-Deck is a very cost effective option for waterproofing your deck. Call us today to locate a Certified Applicator near you.
Q: How do you bridge expansion joints and wall/floor 90º joints?
A: We recommend embedding a material called Polyester Stitch Bond Fabric into the first coat of BG2000 to act as a reinforcement material for high movement areas. It is an inexpensive way to ensure security and rigidity in areas that may be subject to extreme movement over time.
System
Above Grade Waterproofing
DURABLE, LONG-LASTING, WITH PREMIUM AESTHETICS
The MULTI-DECK SYSTEM FOR CONCRETE SUBSTRATES is a multi-layer, waterproofing, and decorative protective coating designed for above grade concrete decks. The system is designed to withstand heavy foot traffic on decks, ramps, walkways, etc.
- Easy To Apply
- Waterproof
- Resists Cracks
- Long-Lasting
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- VAPOR SHIELD
- SCRATCH KOTE*
- MULASTICOAT
- KRETE KOTE*
- COLORSEAL
**TOP COAT may be substituted for KRETE KOTE
- Per Gallon: 75 – 150 ft 2
- Per Bag: 175 ft 2
- Per Gallon: 45 – 50 ft 2
- Per Bag: 125 – 150 ft 2
- Per Gallon: 150 – 175 ft 2
Apply Vapor Shield with a pump sprayer in conjunction with water, back to back. Repeat for a total of 2 coats. Allow 24 hours to dry.
Apply Scratch Kote 2000 with a hopper gun, pressure sprayer or a ¾”-1¼” nap roller. Applied material should peak, not slump.
Stir with hand paddle. Roll, brush or spray Mulasticoat over the area to be waterproofed in two (2) coats. Embed Polyester Stitch Bond Fabric immediately during the application of the first coat over all flashing, plane changes, and joints and apply additional material on top of it. Allow to dry thoroughly between coats.
Apply Krete Kote or Top Coat in 2 steps: a base coat, and a texture coat. Apply a smooth thin layer with a trowel, sprayer or magic trowel and allow to dry. Then apply a texture on top top desired aesthetic look.
Apply the diluted COLORSEAL with nap roller for the 1st coat with very firm pressure. (1/2” nap roller for smooth and 3/4” nap roller for rough surfaces). Allow a minimum of one (1) hour to dry. For the 2nd coat, apply at full strength. Airless sprayers may be used for the 2nd and final coat. Allow final coat a minimum of 24 hours before placing area into use. Will fully cure in 14 days, during which care should be exercised against excessive abuse.
Q: Can Wood Multi-Deck be applied over my existing waterproofing?
A: No, it is best practice to remove an old, failing system before applying a new waterproofing system such as The Multi-Deck System – Concrete Substrates.
Q: Is Vapor Shield Necessary?
A: Yes. The Vapor Shield absorbs into the concrete to form a gel-like barrier to prevent bond-breaking minerals from migrating to the surface where the waterproofing (Scratch Kote 2000 & Mulasticoat) rests.
Q: Is Multi-Deck expensive?
A: Comparing different systems on the market, Multi-Deck is a very cost effective option for waterproofing your deck. Call us today to locate a Certified Applicator near you.
Q: How do you bridge expansion joints and wall/floor 90º joints?
A: We recommend embedding a material called Polyester Stitch Bond Fabric into the first coat of Mulasticoat to act as a reinforcement material for high movement areas. It is an inexpensive way to ensure security and rigidity in areas that may be subject to extreme movement over time.
System
Above Grade Waterproofing
THE NEW INDUSTRY STANDARD FOR TOPPING SLAB WATERPROOFING
BG 2000 is a unique Acrylic Waterbased coating which forms an elastomeric waterproofing membrane with excellent bonding characteristics to most building materials including Plywood, OSB, Concrete, Concrete Block, Primed Metal, and many more. This system is specifically designed for TOPPING SLAB UNDERLAYMENT WATERPROOFING applications for most concrete mixes.
- High Flexibility
- Durable
- Cost-Effective
- Easy to Apply
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- BG2000
- Per Gallon: 35-45 ft 2
On prepped surface (see system instructions) Spray one (1) heavy coat or roll two (2) coats of BG 2000 at a coverage of 60 mil thickness (wet) over area to be waterproofed. Allow to dry for 24 hours.
Tensile Bond Adhesion to Concrete Tensile Strength
Method: ASTM C-297 Result: 335 psi (coh/adh)
Tensile Strength
Method: ASTM D-412 Result: 399 psi
Elongation
Method: ASTM D-412 Result: 319.3%
Hydrostatic Head
Method: 12” Water/Film @ 40mil Result: Pass 96 Hrs/no effect
Hydrostatic Pressure
Method: ASTM C-1306 Result: Pass >45 psi*
*The test procedure only calls for taking the pressure to 45 psi but after passing so easily, test was taken up to 80 psi for 3 hours and surface still did not leak.
Q: What makes the BG2000 UL System solution better than a sheet membrane?
A: There are pros and cons to both types of systems, but the main reason a liquid applied membrane like BG2000 is better than a sheet membrane product is because there are zero seams, which are vulnerable points where water can penetrate the surface to the substrate .
Q: Can BG2000 be applied to green concrete?
A: For applications with at least one exposed side, YES. As long as it is firm to touch and cleaned of mold releases and other impurities. Things like: poured in place retaining walls, freshly built block walls, etc. are perfect applications for BG2000.
Q: Is BG2000 oil-based?
A: No, there is no asphalt emulsion in BG2000. Unlike many competitors that claim to be “water-based” but also contain petroleum byproducts, BG2000 is made from 100% Water born acrylics and contains ZERO ASPHALT EMULSION.
Q: Is BG2000 expensive?
A: No, when used in replace of lower end asphalt products consumers see a cost decrease due to its higher coverage rates, lower application time, and clean up time/ease.
Q: How do you bridge expansion joints and wall/floor 90º joints?
A: We recommend embedding a material called Polyester Stitch Bond Fabric into the first coat of BG2000 to act as a reinforcement material for high movement areas. It is an inexpensive way to ensure security and rigidity in areas that may be subject to extreme movement over time.
System
Above Grade Waterproofing
REVIVE & PROTECT.
The Multicoat Parking Garage Restoration Systems offer a highly effective solution for both weatherproofing and waterproofing needs. Additionally, its high flexural strength, impact and abrasion resistance, and resistance to water and moisture penetration make it a superior choice over other repair materials, providing a long-lasting solution for restoring and maintaining parking garage surfaces.
- Easy To Apply
- Fast Curing
- High Strength
- High Flexibility
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- VAPOR SHIELD*
- SCRATCH KOTE
- MULASTICOAT*
- KRETE KOTE
- COLORSEAL*
- Per Gallon: 75 – 150 ft 2
- Per Bag: 175 ft 2
- Per Gallon: 45 – 50 ft 2
- Per Bag: 125 – 150 ft 2
- Per Bag: 200 – 300 ft 2
Apply Vapor Shield with a pump sprayer in conjunction with water, back to back. Repeat for a total of 2 coats. Allow 24 hours to dry.
Apply Scratch Kote 2000 with a hopper gun, pressure sprayer or a ¾”-1¼” nap roller. Applied material should peak, not slump.
Stir with hand paddle. Roll, brush or spray Mulasticoat over the area to be waterproofed in two (2) coats. Embed Polyester Stitch Bond Fabric immediately during the application of the first coat over all flashing, plane changes, and joints and apply additional material on top of it. Allow to dry thoroughly between coats.
Apply Krete Kote or Top Coat in 2 steps: a base coat, and a texture coat. Apply a smooth thin layer with a trowel, sprayer or magic trowel and allow to dry. Then apply a texture on top top desired aesthetic look.
Apply the diluted COLORSEAL with nap roller for the 1st coat with very firm pressure. (1/2” nap roller for smooth and 3/4” nap roller for rough surfaces). Allow a minimum of one (1) hour to dry. For the 2nd coat, apply at full strength. Airless sprayers may be used for the 2nd and final coat. Allow final coat a minimum of 24 hours before placing area into use. Will fully cure in 14 days, during which care should be exercised against excessive abuse.
Q: Can you use obtain a different finish than a standard cement look?
A: Yes, any of Multicoat’s Decorative Overlay systems can be a part of the Parking Garage Restoration System.
Q: Do any products in this system require specialized safety equipment?
A: No, these materials are green friendly, water-based, and low VOC. We do advise using a respirator when mixing any dry mix. You should always avoid breathing in any sand, resin, and other additives as it could cause irritation of the lungs down the road.
Q: Is The Parking Garage Restoration System expensive?
A: The Parking Garage Restoration System is cost effective in both material and labor but does not sacrifice any quality to do so.
Q: How do you bridge expansion joints and wall/floor 90º joints?
A: We recommend embedding a material called Polyester Stitch Bond Fabric into the first coat of Mulasticoat to act as a reinforcement material for high movement areas. It is an inexpensive way to ensure security and rigidity in areas that may be subject to extreme movement over time.
System
Pool Restoration
THE INDUSTRY BENCHMARK
The Scratch Kote 2000 System is designed to not only bond new pool surfaces to substrates, but also to enhance the performance of that new surface during its installation, curing, and lifespan. Using large aggregate and enhanced polymer blends, Scratch Kote 2000 grips and sticks as well as resists the elements to prevent delamination. To protect your elevated pool finish, Scratch Kote 2000 is the only choice.
- High Bond Strength
- Reduces Modeling
- Water Resistant
- Easy to Apply
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- VAPOR SHIELD
- SCRATCH KOTE
- Per Gallon: 75 – 150 ft 2
- Per Bag: 175 – 200 ft 2
*OPTIONAL – Apply Vapor Shield to the substrate to reduce the green window of concrete, prevent efflorescence, and/or resist hydrostatic pressure coming through wall. Apply with a pump sprayer in conjunction with water, back-to-back. Repeat for a total of 2 coats. Allow 24 hours to dry.
Apply Scratch Kote 2000 or 2-Part with a hopper gun, pressure sprayer or a ¾”-1¼” nap roller. Applied material should peak, not slump. Allow to cure for 12 hours before plastering.
Weatherometer
ASTM G-23: 2000 hrs. – Passed
Compressive Strength
ASTM C-109: 45 days air cured. 2595 psi
Tensile Strength
ASTM C-190: 457 psi
Bond Strength(Flatwise Tension)
ASTM-C 297: 225 psi
Abrasion
ASTM 1242A: 1000cyc-1000gms Passed
50 Cycle Freeze Thaw
ASTM C-67: Passed
Flexural Strength
ASTM-D-790: Modulus of Rupture – 770psi
Impact Resistance
MIL D-3134F: Passed
For Safety Data Sheets, visit our “Resources” page
Q: How long until I can apply SCRATCH KOTE 2000 to the pool shell?
A: Once a pool shell is installed, it is best to wait at least 24 hours. For VAPOR SHIELD, you may spray it the moment the shell is hard.
Q: Do I need to remove trim tile prior to application of SCRATCH KOTE 2000?
A: Yes you do. Scuffing the tile will not provide the proper adhesion necessary for proper performance.
Q: Does Scratch Kote 2000 help even the hydration rate of new plaster?
A: Yes, SCRATCH KOTE 2000 aids in even curing and creates even suction to help reduce modeling of plaster and/or pebble pool finishes.
Q: Can Scratch Kote 2000 be applied over exposed rebar?
A: No, you must patch that area of the pool shell with a rust inhibitor like SPEED MIX, then apply the SCRATCH KOTE 2000.
System
Pool Restoration
THE INDUSTRY BENCHMARK…IN 2 PARTS.
Like The Scratch Kote 2000 System, the 2-Part Scratch Kote System is designed to not only bond new pool surfaces to substrates, but also to enhance the performance of that new surface during its installation, curing, and lifespan. Using large aggregate infused cement mix with a Liquid Catalyst loaded with an enhanced polymer blend, 2-Part Scratch kote grips and sticks as well as resists the elements to prevent delamination. To protect your elevated pool finish, Scratch Kote Systems are the only choice.
- High Bond Strength
- Reduces Modeling
- Water Resistant
- Easy to Apply
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- VAPOR SHIELD
- SCRATCH KOTE 2-PART
- Per Gallon: 75 – 150 ft 2
- Per Unit: 300-600 ft 2
*OPTIONAL – Apply Vapor Shield to the substrate to reduce the green window of concrete, prevent efflorescence, and/or resist hydrostatic pressure coming through wall. Apply with a pump sprayer in conjunction with water, back to back. Repeat for a total of 2 coats. Allow 24 hours to dry prior to application of Mulasticoat
Apply 2-Part Scratch Kote with a hopper gun, pressure sprayer or a ¾”-1¼” nap roller. Applied material should peak, not slump.
Weatherometer
ASTM G-23: 2000 hrs. – Passed
Compressive Strength
ASTM C-109: 45 days air cured. 2595 psi
Tensile Strength
ASTM C-190: 457 psi
Bond Strength(Flatwise Tension)
ASTM-C 297: 225 psi
Abrasion
ASTM 1242A: 1000cyc-1000gms Passed
50 Cycle Freeze Thaw
ASTM C-67: Passed
Flexural Strength
ASTM-D-790: Modulus of Rupture – 770psi
Impact Resistance
MIL D-3134F: Passed
For Safety Data Sheets, visit our “Resources” page
Q: How long until I can apply 2-PART SCRATCH KOTE to the pool shell?
A: Once a pool shell is installed, it is best to wait at least 24 hours. For VAPOR SHIELD, you may spray it the moment the shell is hard.
Q: Do I need to remove trim tile prior to application of 2-PART SCRATCH KOTE?
A: Yes you do. Scuffing the tile will not provide the proper adhesion necessary for proper performance.
Q: Does 2-PART Scratch Kote help even the hydration rate of new plaster?
A: Yes, 2-PART SCRATCH KOTE aids in even curing and creates even suction to help reduce modeling of plaster and/or pebble pool finishes.
Q: Can 2-PART Scratch Kote be applied over exposed rebar?
A: No, you must patch that area of the pool shell with a rust inhibitor like SPEED MIX, then apply the 2-PART SCRATCH KOTE.
System
Above Ground Structures
THE (GREEN) INDUSTRIAL STRENGTH POND SOLUTION
Multicoat PONDS & WATER FEATURES (AG) System offers a completely waterproof solution to projects that are subject to high movement, water loss, and/or are located above the soil level. This membrane driven solution provides a long-lasting barrier from all elements and risks from harming your project. This system should be chosen cautiously over our universal SHIELD KOTE system in areas that are on grade or below grade to prevent issues stemming from negative side hydrostatic pressure.
- Easy To Apply
- Easy to apply
- Easy to apply
- Easy to apply
- FIRE / SALT
- FREEZE / THAW
- UV
- IMPACT / ABBRASION
- *VAPOR SHIELD
- SCRATCH KOTE
- *MULASTICOAT
- *POND KOTE
- Per Gallon: 75 – 150 ft 2
- Per Bag: 125 – 150 ft 2
- Per Gallon: 70 – 90 ft 2
- Per Bag: 120 ft 2
Apply Vapor Shield with a pump sprayer in conjunction with water, back to back. Repeat for a total of 2 coats. Allow 24 hours to dry.
Apply Scratch Kote 2000 with a hopper gun, pressure sprayer or a ¾”-1¼” nap roller. Applied material should peak, not slump.
Stir with hand paddle. Roll, brush or spray Mulasticoat over the area to be waterproofed in two (2) coats. Embed Polyester Stitch Bond Fabric immediately during the application of the first coat over all flashing, plane changes, and joints and apply additional material on top of it. Allow to dry thoroughly between coats.
Using a trowel, hopper gun, or magic trowel, apply Pond Coat to the surface at the desired thickness as long as it is under 1/4″. In some cases, shrinkage cracks may appear, simply apply extra material to those areas upon completion.
MULASTICOAT
Tensile Strength
ASTM D2370 PSI 203
Elongation
ASTM 2370 1148%
Tensile Bond Adhesion, PSI
ASTM C297 162 Cohesive
Static Hydrostatic Pressure
ASTM C 1306 Pass>45PSI
Hydrostatic Head
12” Water/Film@40mil Pass 96hrs/No Effect
6 Low Temperature Flexibility
Mandrel Bend ASTM D522 ½“ Room Temp Pass
1” @ -5°F Pass
½“ @ -5°F Pass
POND KOTE
Density, g/cc
175
Compressive Strength (28 day)
3125 psi
Flexural Strength (28 day)
1375 psi
Water %
2250%
Toxicity (96 hr LC50)
Passed*
*Toxicity testing was done on flat head minnows and rainbow trout, with no adverse affects to either species of fish
SCRATCH KOTE 20000
Weatherometer
ASTM-G 23 2000 hrs – Passed
Compressive Strength
ASTM-C 109 45 days air cured – 2595psi
Tensile Strength
ASTM-C 190 457 psi
Bond Strength(Flatwise Tension)
ASTM-C 297 225 psi
Abrasion
ASTM-1242A 1000cyc-1000gms Passed
50 Cycle Freeze Thaw
ASTM-C 67 Passed
Flexural Strength
ASTM-D 790 Modulus of Rupture – 770psi
Impact Resistance
MIL-D3134F Passed
For Safety Data Sheets, visit our “Resources” page
Q: Is this fish friendly?
A: Yes. Allow material to dry 7 to 10 days prior to filling with water. After filling, run circulation pumps/filters followed by a light brushing to remove any surface containments prior to adding fish. Longer dry time will be required for interior applications.
Q: Can I add colorant to the POND KOTE?
A: Yes as long as you mix the colorant with the water prior to adding the dry mix to it. You should not mix the colorant in after it has been mixed with water.
Q: Do I have to strip off any old material from the substrate?
A: Yes, we recommend approximately 92-100% removal of all old coatings prior to the application of this system.
Q: Can I just use the MULASTICOAT as a patch for my existing pond? I only have a few spots that are leaking.
A: No. MULASTICOAT creates a uniform membrane and is not designed to be a “universal” material that can bond with any coating.
